Display Center Of Gravity Inventor Drawing Assignments

Posted on February 6th by Mark Lancaster, Synergis Manufacturing Product Support

Did you know there are five different Bill of Materials structures you can use to control your Bill of Materials in Inventor?

Are you now asking yourself what is a Bill of Material structure? A Bill of Material structure allows the user to control how the Inventor Bill of Materials (BOM) will appear based on the intended model design.

For this article I will review each of these structures and provide an example on how they can be useful in controlling your BOM. At the end of this article I will cover how to apply them to your Inventor files and also demonstrate how it’s possible to over-ride it for a given assembly.

Normal:

By default the “NORMAL” structure is assigned to parts and assemblies you create in Inventor. Under this structure your parts or assemblies appear as a single line entry in the BOM or it acts like a normal Bill of Materials would.

 

Phantom:

Although the “PHANTOM” structure can be assigned to parts, it’s really structured for sub-assemblies within your model. When it’s assigned to an assembly, the children that make up the assembly are actually promoted to the next level in the BOM and the assembly itself is never listed.

For example, in my piping manifold assembly I need to add the hardware as shown to the four (4) flagged connections. So instead of inserting, constraining, and patterning the hardware at this level, I elected to create a phantom hardware sub-assembly for one (1) flagged connection. Now when I look at my BOM, I only see the total hardware quantity and not the four (4) sub-assemblies I actually placed into my model.

Purchased:

This BOM structure is intended for all purchased components and I recommend assigning it to any component that you purchase for your design. Whether you created the model or it was downloaded, assigning this structure will allow you:

  1. The ability to filter (include/exclude) your purchased components on the drawings parts list.
  2. To sort/group the BOM Structure column in the BOM view no matter which item number is assigned to your purchased components.

This structure can also be assigned to assemblies that your company purchases or manufacturers. When an assembly is assigned this type of structure the following occurs:

  1.  The assembly is listed as a single line item in the “PARTS ONLY” list
  2.  Its children
    1.  Will never appear in the “PARTS ONLY” list and are excluded for any BOM quantity calculation.
    2.  Will appear and be numbered when viewing “all levels” under the “STRUCTURED” list. Under this condition the child are shown like a normal assembly would be in the BOM view.

Referenced:

A “REFERENCED” structure allows the user to place parts and sub-assemblies into a model that are not part of the actual design. For example, I want to place the customer’s pump (an Inventor part) and my piping manifold together in a skid assembly to ensure I’m designing the correct piping supports.

However, I don’t want the customer’s pump listed in my BOM, so I apply the “REFERENCED” structure to it. Not only does it remove it from the BOM, it also excludes the pump’s mass/volume from the overall calculation of the skid design.

When the “REFERENCED” structure is assigned to an assembly, the entire assembly and its children are not reported in the BOM and/or do not participate in any quantity, volume, or mass calculations. Even if one or all of the children have a “NORMAL” and/or “PURCHASED” structure assigned to them, the “REFERENCED” assembly still  takes precedent.

For example, if I apply the “REFERENCED” structure to my piping manifold and set the customer pump back to “NORMAL”, only the pump and related connecting components are shown in the BOM.

On the drawing side, when a part or assembly is assigned the “REFERENCED” structure, by default will appear as dashed lines and may not appear correctly within your drawing views.

“REFERENCED” models are excluded from the drawing view boundary box calculation and depending on its location, can be clipped as shown above. Changing the line style or correcting the clipping aspect, can be accomplished by editing the drawing view, “MODEL STATE” tab, and the options shown below.

Inseparable:

This BOM structure works in the same fashion as a “PURCHASED” assembly except it was designed for assemblies that are always grouped together (i.e. weldment assembly).  However, if a component of the “INSEPARABLE” assembly is listed as “PURCHASED”, it will also be listed in the “PARTS ONLY” list. It is designed this way to ensure these (purchased) components are also identified for purchasing. For example, if I make my piping manifold “INSEPERABLE”, its piping components will also appear in the “PARTS ONLY” list.

Now let’s talk about how to assign these structures to your Inventor files. An Inventor part or assembly can be assigned these structures by accessing the “Bill of Materials” tab of its “Document Settings”. By default the structure is set to “NORMAL”.

Another method is to access the assembly “Bill of Materials” and change the structure under the “BOM Structure” column.

Depending on the file type (i.e. content center) and/or its Vault status, modifying at this level may not be allowed.

Finally there may come a time when an Inventor part (or sub-assembly) needs to be shown in a given assembly as a reference component. However, if you change the BOM structure of the part it will impact every BOM it participates in. To over-ride the current part’s BOM Structure in a given assembly you can do one of the following:

  •  Right mouse click on the part (or sub-assembly) in the browser/graphic window and select BOM Structure/Reference

Over-ride is only applied to this occurrence in the assembly

  • Right mouse click on the part in the browser/graphic window and select IProperties/Occurrence tab

So by over-riding the BOM structure of my piping manifold in this upper assembly, the actual structure still remains intact

Hopefully this information has helped you to understand the Bill of Materials Structures within Inventor and gives you another tool in controlling your model’s BOM.

Have a question for Mark or any of our technical staff? Contact us, visit the Synergis website or subscribe to our blog.

Like this:

LikeLoading...

How to Display the COG in an Inventor Drawing

Posted by: Kristin Prokop | June 13th, 2012 | Autodesk

Issue:Want or need to show and dimension to the COG (center of gravity) in an Inventor part or assembly drawing view.

Solution:After placing your drawing views in a drawing whether an individual part or a complete assembly, right click on the part or assembly in the model browser tree and right click onCenter of Gravityin the context menu.

Notice there is now a cross indicating the COG in that part view

You can now dimension and or constrain to the COG point.

Overview:Many times while working on a model you may need to know the exact dimension to the COG in a certain view. This feature will allow you to accomplish knowing exactly where the COG is located and allow for dimensioning and constraining

Summary:This feature will work in both IDW and DWG formats

Tags: inventor


One thought on “Display Center Of Gravity Inventor Drawing Assignments

Leave a Reply

Your email address will not be published. Required fields are marked *